The Ultimate Guide to Apple’s Proprietary SSDs

All Articles Featured Discussion

Remember the good ol’ days of carrying a spare battery, upgrading your own RAM, maybe even adding a second hard drive? If you’re an Apple user, those luxuries may be behind us, but upgrading your own solid state drive is still a privilege the Apple overlords allow us to have, for now that is.

Despite retaining the ability to upgrade your own SSD, ever since Apple introduced their proprietary “blade” SSDs in 2010, the task hasn’t been as simple as it once was. Apple talks up read and write speeds, but they rarely dive into the nitty gritty details of the technology behind the SSDs they use — drives specially designed only for Apple computers.

After countless questions, both from customers and our own staff, we decided to start our own investigation into the hardware involved. You have to be a bit of a private eye to uncover the secrets behind these drives, and the deeper we looked, the more surprises we found.

Table of Contents

Apple SSD Line-up Old to New LTR: Gen. 1 SSD, Gen. 2B, Gen. 2A, Gen. 3A (comparable to Gen. 4A and Gen. 4C), Gen. 3B (comparable to Gen. 4B), Gen. 5B, Gen. 5A

SSD Interfaces Compared

Every hard drive or solid state drive you’ve used in the past ten years is likely to have used either a SATA interface, or more recently a PCI Express interface. If you’re into vintage computers and you think patience is a virtue that can only be honed by waiting for programs to respond, maybe you’re still rocking a drive with a PATA interface. If you are, it’s time to get up to speed!

Ever faster drive technology, brought about by faster spinning disks, increased cache, advances in controller architecture, and a host of other factors keeps pushing the host interface to become the bottleneck for read and write speeds. Luckily, advances in host interfaces invariably stay ahead of the pace of drive technologies, always allowing room to push speeds a bit farther.

What is SATA?

SATA (Serial Advanced Technology Attachment) refers to the technology standard for connecting hard drives, solid state drive, and optical drives to the computer’s motherboard. The SATA standard’s been in use for many years and is still the most prevalent interface for connecting internal storage drives.

The SATA standard has now undergone three major revisions, resulting in connectors that are identical in appearance (hurray for backwards compatibility), but with bandwidth doubling each time. This can cause some confusion in the event that you connect a hard drive that supports the SATA III standard into a SATA II connector, creating a bottleneck at the SATA II interface that will limit the potential bandwidth of the drive. But as it applies to SSDs, if you’re not using a SATA III connection, it’s safe to assume you’re limiting the potential of your drive. And even if you’re using a SATA III interface, you’re still probably limiting your SSD. In short, SATA just wasn’t made for solid state drives.

SATA Performance
Interface Raw Transfer Rate Encoding Effective Data Rate Effective Data Rate
SATA I 1.5Gb/s 8b/10b 1.2Gb/s 0.15GB/s
SATA II 3Gb/s 8b/10b 2.4Gb/s 0.30GB/s
SATA III 6Gb/s 8b/10b 4.8Gb/s 0.60GB/s

What is PCIe?

Peripheral Component Interconnect Express (PCIe) is a computer bus standard with incredibly high bandwidth potential, and is the fastest bus option that most computers have available. It’s no wonder that manufacturers moved towards PCIe technology for their bandwidth hungry SSDs. Like the SATA bus standard, PCIe has undergone multiple revisions over the years and is still evolving at breakneck speeds. PCIe 2.0 (which is likely to be the most common PCIe revision found inside in-use computers) maxes out at ~500MB/s with a single channel of throughput. Those speeds may sound a bit slower than SATA III, but PCIe has the advantage of utilizing multiple channels of throughput to accommodate the needs of the connected peripheral.

Two channels of throughput (~1GB/s) not enough for you? Double the number of channels to four and you’ll realize double the data transfer rates, if the connected device can make use of it that is. PCIe bandwidth can be scaled up to 16 and even 32 lanes for a single device, but that’s uncommon in SSDs and primarily reserved for devices like graphics cards which have larger data transfer requirements. Most PCIe SSDs will have either 2, or more recently, 4 channels of throughput.

In 2011 the PCIe 3.0 revision was released, and finally brings more to the table than just the ability to add additional channels. PCIe 1.0 and 2.0 both use 8b/10b encoding to transmit data (the same as SATA), meaning that for every 8 bits of data sent, the data is sent via a 10 bit line code. In other words, 2 of the 10 bits are just overhead necessary to transmit the rest of the data. That 20% overhead eats into the potential bandwidth of an interface, resulting real world bandwidth that’s 20% lower.

PCIe 3.0 introduced the much more efficient 128b/130b encoding, resulting in only only ~1.5% overhead to eat into the potential bandwidth.

PCIe Speed Comparison Chart

Interface Raw Data Rate Encoding Effective Data Rate Channels Total Effective Data Rate
PCIe 1.x 2.5GT/s 8b/10b 2.0Gb/s 2 500MB/s
PCIe 1.x 2.5GT/s 8b/10b 2.0Gb/s 4 1.0GB/s
PCIe 1.x 2.5GT/s 8b/10b 2.0Gb/s 8 2.0GB/s
PCIe 1.x 2.5GT/s 8b/10b 2.0Gb/s 16 4.0GB/s
PCIe 1.x 2.5GT/s 8b/10b 2.0Gb/s 32 8.0GB/s
PCIe 2.x 5GT/s 8b/10b 4.0Gb/s 2 1.0GB/s
PCIe 2.x 5GT/s 8b/10b 4.0Gb/s 4 2.0GB/s
PCIe 2.x 5GT/s 8b/10b 4.0Gb/s 8 4.0GB/s
PCIe 2.x 5GT/s 8b/10b 4.0Gb/s 16 8.0GB/s
PCIe 2.x 5GT/s 8b/10b 4.0Gb/s 32 16.0GB/s
PCIe 3.x 8GT/s 128b/130b 7.9Gb/s 2 1.98GB/s
PCIe 3.x 8GT/s 128b/130b 7.9Gb/s 4 3.95GB/s
PCIe 3.x 8GT/s 128b/130b 7.9Gb/s 8 7.90GB/s
PCIe 3.x 8GT/s 128b/130b 7.9Gb/s 16 15.80GB/s
PCIe 3.x 8GT/s 128b/130b 7.9Gb/s 32 31.60GB/s

AHCI vs NVMe

Advanced Host Controller Interface (AHCI) was originally created when storage devices still used spinning magnetic disks to store data. and communicated data based on the speeds and needs of those devices. AHCI was versatile enough to work with SSDs while SSDs were still in their infancy, but it’s been a hindrance to transfer rates for a few years now.

Enter NVMe, or Non-Volatile Memory Express. NVMe was created specifically to work with SSDs, reducing the latency and allowing for larger amounts of data to be transferred at a single time, making better use of modern multi-core processors. NVMe becomes especially important with PCIe SSDs, where AHCI starts to bottleneck the speeds. By the time the PCIe 3.0 revision came out, NVMe became essential to reach the full potential throughput of the drives.

Apple's Proprietary Connectors

When Apple released their first “blade” solid state drive in the Late 2010 release of the MacBook Air, they still used established mSATA interface technology, but ditched the traditional SATA and mSATA form factors found in most laptops at that time, instead opting for a custom connector that’s never been used by another manufacturer before or since. With the 2010 MacBook Air, Apple began a new trend of developing proprietary connectors and form factors that eventually pervaded the entire Apple lineup and ushered in an era of drives that, while easily replaceable, were not so easy to find.

Many people incorrectly assume the connectors are one of the M.2 variants found in many PCs, but to date, Apple has still never used a standard M.2 connector. And unlike M.2 pin arrangements, Apple’s connectors were never given distinguishing names, so from this point on I’ll just refer to the connectors by their pin arrangements as described in the image below.

Comparison of proprietary SSD connectors.

A History of Apple SSD Releases

Generation 1: MacBook Air (Late 2010 - Mid 2011)

For the Late 2010 and Mid 2011 releases of the MacBook Air 11″ (Model A1370) and MacBook Air 13″ (Model A1369), Apple’s desire to shave down the height of the already thin original MacBook Air necessitated a switch to a thinner drive. Rather than use a 2.5″ SATA SSD as seen in the rest of Apple’s product lines, or even the 1.8″ SSD found in the original MacBook Air, Apple switched to an even thinner, custom drive. This “Generation 1” drive utilized a proprietary 6+12 pin connector, but still used an mSATA III interface limited to 6Gb/s; the same limitation as the other product lines released during this period.

Both Samsung and Toshiba manufactured Apple’s Generation 1 SSDs, but rather notoriously, the Toshiba drives performed significantly worse than their Samsung counterparts. Both drives performed up to Apple’s advertised specs, mind you, but MacBook Air customers were subject to an SSD lottery, with Samsung drives performing reads and writes at ~1.5x-2.0x the speed of their Toshiba counterparts. Apple seems to have learned from this oversight and later generations of SSDs never again saw such a large distinction between the drives of different manufacturers.

Generation 2

The second generation of Apple SSDs saw the expansion of the blade style drives into the MacBook Pro laptops and iMac desktops. The Gen. 2 drives were faster than than the previous generation but still used the mSATA III interface — finally approaching the maximum throughput capable of the SATA III specification.

The Gen. 2 drives were characterized by their use of two distinctly different drives; the shorter, wider Gen. 2A drive used in the MacBook Pro and iMac computers, and the taller, thinner Gen. 2B drive used in the MacBook Airs. Both Gen. 2A and 2B drives use the same mSATA 3 interface and the same 7+17 Pin connector type. Despite the use of identical connectors and interfaces, the drives aren’t truly compatible because the space allotted in each computer simply isn’t designed to fit the other drive type.

MacBook Pro (Mid 2012 - Early 2013)

With the release of the first MacBook Pro with “Retina” screen, Apple began including SSDs standard in the MacBook Pro line, and in fact the only storage device interface is the single 7+17 Pin SSD connector. The Gen. 2A SSDs used by these MacBook Pro laptops were offered in 128GB, 256GB, 512GB, and 768GB capacities, and manufactured again by Samsung, but also by SanDisk.

Both the 13″ and 15″ MacBook Pro laptops use the same drives, and either MBP can have any of the four SSD capacities installed.

iMac (Late 2012 - Early 2013)

The Late 2012 and Early 2013 iMacs had a rather different arrangement, with a traditional 3.5″ SATA III HDD standard, but the Late 2012 release also unveiled the Fusion Drive. Apple’s Fusion Drive pairs a larger capacity traditional hard drive with a smaller capacity solid state drive, offering much of the performance benefits of an SSD, but in a more cost-effective package. The operating system displays the two drives as a single drive to the user, but behind the scenes optimizes file storage so that files requiring more frequent access and files that see the most benefits from quick read times are stored on the SSD, while the majority of the files are stored on the HDD.

In order to utilize Apple’s fastest SSDs in the Fusion Drive setup, the iMac logic boards now included Apple’s proprietary 7+17 Pin SSD connector, in addition to one of the two SATA III connectors found in previous iMacs, allowing you to install any combination of SATA and Apple SSDs. It’s not necessary to use the SSD in the Fusion Drive arrangement, and the two drives can act independently of each other if desired. The SSD connector can use any of the Gen. 2A options (128GB, 256GB, 512GB or 768GB), while the SATA connector can accommodate any 3.5″ SATA HDD or SSD, or a 2.5″ SATA drive when using a 2.5″ to 3.5″ adapter.

Regardless of how the iMac was originally configured, both the iMac 21.5″ and iMac 27″ always had the 7+17 Pin connector present on the logic board, opening the door to later upgrade with a blade SSD. For anyone planning to upgrade their iMac that was not originally configured with a blade SSD, it should be noted that while the connector is present, the single screw that secures the SSD is missing. It’s a pretty uniquely shaped screw and you’re not likely to find it at your local hardware store, so make sure to purchase one before you go to the hassle opening up the iMac.

MacBook Air (Mid 2012)

As mentioned above, the Gen. 2B drives have a different form factor, but use the same interface and connector as their Gen. 2A counterparts. The 2B read/write speeds are noticeably slower, likely due to engineering constraints from the smaller footprint of the 2B drives.

Another likely result of the engineering constraints is the absence of a 768GB option. Samsung and Toshiba manufactured the Gen. 2B drives, which came in 64GB, 128GB, 256GB and 512GB options, all of which are interchangeable in the Mid 2012 releases of the MBA 11″ (model A1465) and MBA 13″ (model A1466).

Generation 3

It was clear with the Gen. 2 drives that mSATA’s 600MB/s limitation would not allow for further speed increases, so Apple’s next generation of drives began using a PCIe 2.0 x2 interface, bringing about the most substantial performance increases to date. Performance varies wildly depending on the combination of device, capacity, and manufacturer but the fastest Gen. 3 configurations can perform at more than double the speeds of the fastest Gen. 2 drives.

Generation 3 also saw a consolidation of the connector used, with almost all Gen. 3 drives compatible with all Mid 2013 through Mid 2015 releases of Apple computers. Of course, a few exceptions apply; notably the MacBook Air and iMac 21.5″.

Not only are the SSDs cross-compatible between the different devices, but the different computers do in fact share the exact same drives. The SSDs were manufactured by Samsung, SanDisk, and Toshiba, and the same manufacturer part numbers have been found on drives retrieved from all of the different computers. Samsung seems to have appended unique endings (/0A2, /0A4, /0A6, etc.) to drives used in different devices, but the drives all use the same flash controller and our testing has shown zero performance difference between them.

The Gen. 3 solid state drives are all the same form factor (which I’ll refer to as Gen. 3A), except for the 1TB SSD (Gen. 3B) which is the same length, but roughly twice as wide. All Gen. 3 drives use the same 12+16 Pin connector and all share a PCIe 2.0 x2 interface, except for the 1TB Gen. 3B SSD which has a PCIe 2.0 x4 interface, likely due to the larger physical size of the drive which allows for less engineering constraints.

There is one more drive that’s worth mentioning, more as a bit of trivia than anything, but there was also an extremely rare 768GB SSD included in some iMacs during this time. It shares the same Gen. 3B form factor and PCIe 2.0 x4 interface as the 1TB SSD and has comparable read and write speeds. This drive seems to have been phased out not long after Samsung began manufacturing it though, and you’re unlikely to find one unless you’re hunting for it.

All the Gen. 3 drives use AHCI technology, but many of the computers that shipped with Gen. 3 drives support NVMe SSDs as well, allowing for upgrades to later generation NVMe drives.

MacBook Air (Mid 2013 - Early 2014)

As with previous MacBook Air laptops, both the 11″ and 13″ laptops use all the same drives, which included 128GB, 256GB and 512GB capacities, leaving behind the 64GB option found in earlier MacBook Airs.

Interestingly, while the drives are all limited to a PCIe 2.0 x2 interface, the MacBook Air logic boards all support PCIe 2.0 x4, opening up the possibility to upgrade to the faster four channel drives found in Gen. 4.

Mac Pro (Late 2013)

The big revision to the Mac Pro desktop saw big changes to its storage devices as well. The Late 2013 Mac Pro was the first Mac Pro to have a solid state drive standard, the first to natively use PCIe storage, and to the dismay of many power users, the first to support only a single internal storage device.

The Mac Pro supports all capacities (128GB – 1TB) of Gen. 3 SSDs, but originally included drives with heatsinks that are attached with an extremely strong thermally conductive adhesive. It’s generally a safe bet that if Apple’s engineers decided it was necessary, it’s probably necessary, but it’s worth mentioning that the Mac Pros can use the heatsink-less SSDs found in other devices, and our internal testing showed absolutely no difference in SSD temperature when using drives with and without heatsinks, even under stress test conditions.

The Mac Pro’s logic board has the same limitations as the MacBook Air laptops, supporting a PCIe 2.0 x4 connection, allowing for improved performance with later four channel drives. The nMP also supports NVMe SSDs and can upgrade to some of the Gen. 5 drives when running macOS 10.10.3 or later.

MacBook Pro (Late 2013 - Mid 2014)

The Late 2013 and Mid 2014 MacBook Pro laptops both support all generation 3 drive options, and as with the MacBook Airs, while the included drives were PCIe 2.0 x2, the logic boards all support four channel PCIe connections.

The MacBook Pros also support the NVMe protocol, and like the Mac Pro, require macOS 10.10.3 or later.

iMac (Late 2013 - Late 2015)

The 21.5″ iMac originally shipped with either a 1TB SATA HDD, a 1TB Fusion drive (128GB SSD and 1TB SATA 3.5″ HDD), or a 256GB standalone SSD. The 27″ iMac offered the same 1TB Fusion Drive as the standard option, with optional upgrades to a 3TB Fusion Drive (128GB SSD and 3TB SATA 3.5″ HDD), or a standalone SSD in either 256GB, 512GB, or 1TB capacities.

Given that the iMacs have relatively ample free space inside, at least compared the rest of Apple’s product lines, it should come as no surprise that all drive capacities are supported in both the 21.5″ and 27″ iMacs. As with the previous generation, the 27″ iMac always included the PCIe connector on the logic board, but breaking with the previous iMac releases, the 21.5″ iMac only included the PCIe connector if originally configured with a Fusion Drive or standalone SSD when ordered. If a Fusion Drive was not selected at the time of purchase, there’s only an empty space where the PCIe connector would have been, and there’s no way to add the connector to the board, short of replacing the entire logic board.

The 21.5″ iMacs and the 27″ from 2013/2014 only support PCIe 2.0 x2 connections.  All iMacs of this era support NVMe, but the speed increase is more limited in the 21.5″ iMacs and the 2013/2014 27″ iMacs, where the two channel interface acts as a bottleneck.

Mac mini (Late 2014)

Late 2014 was the first Mac mini to support Apple’s blade solid state drives, but it’s extremely limited internal space required a unique solution in order to connect the drive to the logic board. Rather than a 12+16 pin PCIe connector on the logic board where the SSD would connect directly, the Mac mini positioned the SSD on the rear of the plastic hard drive carrier, off to the side of the board, and required a flex cable to connect the SSD.

The flex cable has the 12+16 pin female connector on one side and a female 40 pin mezzanine connector which attaches to the 40 pin male connector on the motherboard. This was the first and last time Apple used this smaller connector for PCIe connections in any of their product lines.

Mac Mini PCIe SSD Connector Close-up PCIe connector on the Late 2014 Mac mini

The connector is present on the board regardless of which storage configuration was initially ordered, so it’s possible to add a PCIe SSD to all Late 2014 Mac minis. If the Mac mini wasn’t originally configured with a Fusion Drive or standalone SSD from the factory, the flex cable will need to be purchased in order to add an SSD afterwards.

The Mac mini motherboard only supports a PCIe 2.0 x2 interface, but does support an upgrade to NVMe SSDs, but like the 21.5″ iMac, the speed increase is a modest 10-15% due to the two channel PCIe bottleneck.

Generation 4

With the release of the first Early 2015 MacBook Air and MacBook Pro laptops, Apple unveiled its fourth generation of blade SSDs. Gen. 4 included a few variations, but for the most part was again used across all the product lines of the time, and even stuck with the same 12+16 Pin connector found in the Gen. 3 drives, making the Gen. 4 drives a great option for upgrading earlier devices.

The Gen. 4 drives all used a PCIe 3.0 x4 interface, with the exception of the drive used in the MacBook Air 11″ which used a newer version (Gen. 4C) of the PCIe 2.0 x4 drives found in the previous generation. I’ll be referring to the 128GB, 256GB and 512GB Gen. 4 drives as Gen. 4A, and the larger 1TB drive as Gen. 4B, similar to the Gen. 3B 1TB drive from the previous generation.

Generation 4 brought massive increases in speeds when compared to their Gen. 3 counterparts, with read and write speeds that are roughly twice that of the previous generation. All the laptops and desktops released during this period could make use of the four channel PCIe connection, but only a few select models could reap the benefits of the PCIe 3.0 technology. For devices that did support a PCIe 3.0 connection to the SSD, read and write speeds were more than doubled. All in all, the fourth generation of solid state drives represented another monumental leap in drive technology.

Then SSDs were manufactured exclusively by Samsung this time around, with the exception of the Gen. 4C drive from the 11″ MacBook Air which was manufactured by Toshiba. The Samsung drives are commonly referred to by the identifier of their flash controller, dubbed UBX — or as it’s printed on the drive, SSUBX. This is quick an easy way to identify the Generation 4 drives from the Gen. 3 Samsung drives which have SSUAX printed on the labels.

MacBook Air (Early 2015 - Mid 2017)

The Early 2015 MacBook Air 11″ was the last release of the 11″ laptop form factor, and while most of the hardware saw only incremental improvements, the SSDs were radically different from the previous generation, and unique amongst the Gen. 4 drives. These new drives, which I’ve distinguished as Gen. 4C, still use the PCIe 2.0 interface, but expanded from two to four PCIe lanes, and most notably,  use the more performant NVMe interface, the first Apple SSDs to do so.

And although using the the same 12+16 pin arrangement and form factor, their firmware renders them incompatible with earlier MacBook Air laptops. The new drives were also now branded “Apple” rather than with the third party manufacturer’s name, although the flash chips on the SSD make it clear that Toshiba and SanDisk were manufacturers.

On the logic board side, the 2015 MacBook Air 11″ uses the same PCIe 2.0 x4 interface found in previous releases, and can also use the more common PCIe 3.0 Gen. 4A drives, albeit limited to PCIe 2.0 speeds. In fact, if the 11″ MacBook Air was configured with a 512GB SSD from the factory, it already included the same Gen. 4A drive found in other Apple computers of the era.

The 13″ MacBook Air used the same Gen. 4A drives as the rest of Apple’s product lines, but didn’t support the PCIe 3.0 connection the newer drives were capable of. Despite the lack of PCIe 3.0 support, the Early 2015 release still saw read/write speeds that were 90-120% faster than the 2013/2014 models. The same Gen. 4A drives are still in use in the most recent Mid 2017 release.

Like the MacBook Air laptops before them, the Early 2015 – Mid 2017 MacBook Airs lack the space to fit the wider 1TB SSDs, and are limited to the 128GB, 256GB and 512GB options.

MacBook Pro (Early 2015 - Mid 2015)

The 2015 releases of the MacBook Pro laptops were also relatively minor upgrades, but again the SSDs brought about a huge speed boost, especially for the 15″ model A1398. Both the 13″ and 15″ computers support the full range of drive capacities and supported four channel connections, but the 15″ MacBook Pro also supported PCIe 3.0.

Both the 13″ and 15″ MacBook Pros also support the NVMe protocol and upgrading to Gen. 5 SSDs can bring a modest speed boost to the 13″ model A1502, but the 15″ model A1398 with its PCIe 3.0 connection really allows the NVMe technology to shine. Read speeds increase by ~40% and write speeds can increase by ~60%.

iMac (Late 2015)

The Late 2015 iMacs see a lot of the same trends found in earlier iMac releases. The 21.5″ iMac only has a PCIe connector on the motherboard if the computer was originally configured with a Fusion Drive or standalone SSD. To the dismay of many people, the 1TB Fusion Drive now only included a 24GB SSD paired with the same 1TB SATA HDD, and continued offering an option for a standalone 256GB SSD. The 27″ iMac also tweaked the 1TB Fusion Drive to include the smaller 24GB SSD, but the 2TB and 3TB Fusion Drives were still paired with the 128GB capacity drives. The 27″ iMac also continued offerings of 256GB, 512GB or 1TB standalone SSDs.

You might have noticed that there had not been a 24GB SSD option until this point in time, and in addition to bringing about a new capacity, the 24GB PCIe 3.0 x4 SSD was also Apple’s first removable NVMe SSD. Another interesting oddity with the 24GB drive is that it’s actually designated as a 32GB drive on its label, with 25% of the available space reserved and unusable to the user. All SSDs have some portion of their capacity reserved to replace bad blocks that have become unreliable with time; a natural wearing down of drives that occurs during the writing process. Reserving a quarter of a drive’s capacity is highly unusual, but considering that the drive is designed to act as a cache for the Fusion Drive and will likely take a lot of wear, it makes total sense that a large segment of the drive would be allocated to replace worn out sections. Unfortunately, this is the only NVMe drive available during this period, and NVMe SSDs didn’t become widespread in Apple’s lineup until Gen. 5.

All of the SSDs found in the Late 2015 iMacs are of the new PCIe 3.0 x4 variety, but the A1418 only supports a PCIe 2.0 x4 connection. The 27″ iMac, on the other hand, is the only device other than the 15″ MacBook Pro to support a PCIe 3.0 x4 connection. Both iMacs support the NVMe protocol though and can upgrade to later Gen. 5 SSDs for a big speed boost.

Generation 5

The fifth generation of Apple SSDs introduced a few major changes. On the performance front, all the Gen. 5 SSDs support the NVMe protocol, and the devices that included these drives all support PCIe 3.0 x4 NVMe connections. These two changes meant that not only are the Gen. 5 drives quite a bit faster, but all the Apple computers of this era were able to reap the full benefits.

Gen. 5 also saw changes to the form factor, now with two distinct SSD types. The Gen. 5A drives used an all-new, significantly smaller form factor, as well as a new 22+34 Pin connector. The Gen. 5B SSDs continue to use the 12+16 Pin connector found in the Gen. 3 and Gen. 4 drives and have the same form factor found in the Gen. 3B and Gen. 4B 1TB drives. Despite the larger connector on the Gen. 5A drive which one might assume could provide more throughput and performance, the Gen. 5B drives have superior read/write speeds, topping out at a whopping ~2,700 MB/s read speed and ~2,350 MB/s write speed.

The generation 5B lineup didn’t just bring massive speed increases, it introduced a major increase in capacity as well with Apple’s first removable 2TB SSD. While the length and width are the same as the 128GB Gen. 5B SSD, the 2TB SSD doubled the maximum storage capacity available in an Apple blade SSD, and because its connector and form factor remained consistent with previous generations, the 2TB drive makes for the biggest, fastest OEM drive that can be used to upgrade Apple devices dating back to 2013.

MacBook Pro (Late 2016 - Mid 2017)

Starting with the Late 2016 release, Apple began releasing two versions of its MacBook Pro laptop: the non Touch Bar (nTB) version, and the version with Touch Bar. Only the 13″ MacBook Pro was offered in the nTB version, and notably, the nTB version is the only MacBook Pro of this release that has a removable SSD. All of the MacBook Pro laptops with a Touch Bar share the same PCIe 3.0 x4 NVMe SSD, but the SSD is soldered to the logic board and is not removable/replaceable. The only way to upgrade the storage on the MacBook Pro with Touch Bar is to replace the entire logic board.

The MacBook Pro 13″ that does have a removable SSD used the Gen. 5A SSDs, and the Late 2016 and Mid 2017 releases are the only two computers to support these drives. The Late 2016 MacBook Pro offered choices of a single 256GB, 512GB, or 1TB SSD, while the Mid 2017 release also introduced a 128GB option, and while nearly all of the drives are compatible with both the 2016 and 2017 releases, there are a couple exceptions.

After extensive testing with every Gen. 5A drive we could get our hands on, it appears that 128GB SSDs with part numbers beginning with 656-0074 and 256GB SSDs with part numbers beginning with 656-0076 are only compatible with the model A1708 laptops from the Mid 2017 release.

If you’ve got this far and are looking for more, I’m sorry to say this is the end of the line. This post has attracted more attention than our average post so I’m currently in the process of adding more and better information. I’m planning on adding lots more info, speed tests, part numbers and more upgrade guides. This post ain’t dead yet, so check back soon.

In the meantime, if you have and questions or comments, leave them below because I probably already have the answer.

About The Author

Cody Henderson

Cody's the guy who started Beetstech (in his grandma's dining room!) and he's been tinkering with, tearing apart, and sometimes putting back together electronics and mechanical devices since he was a young lad. When he's not writing blog posts, he's jumping from role to role here at Beetstech, doing whatever needs to be done to make Beetstech even better.

334
Leave a Reply

159 Comment threads
175 Thread replies
290 Followers
 
Most reacted comment
Hottest comment thread
184 Comment authors
Recent comment authors
  Subscribe  
Notify of
Member
jackrmccabe

What is the fastest PCIe NVME SSD that will fit in my iMac17,1 Retina 5K Late 2015 27″A1419?

Guest
SUHAS VAZE

I have iMac Late 2015 27 inch (iMac 17,1) – With Fusion Drive – 24GB blade SSD and 1 TB HDD. If I have to upgrade the Blade SSD to Samsung 970 EVO NVME M.2 , Is it possible with any sintech adapters available on Amazon? or any other options to upgrade the blade SSD?

Guest
Olivier P

Hi, First thanks so much for this detailed blog on Apple SSD. I was looking for such a thing for a long time ! Your blog is giving very valuable information about SSD for iMac up to iMac Late 2015. I just bought an iMac 2017 4k 21″ 1 To Fusion on the refurb and I’m wondering which SSD could fit to replace the ridiculous 32Gb installed. I’m looking for a 1To SSD. In “About my mac” I have some info but I’m not sure if it will be sufficient to choose the right one. Can you help and provide… Read more »

Guest
Carl Chen

Great Guide! Super thanks for the effort. My MacBook Air (2015) has a Model MZ-JPV512R/0A2 512GB SSUBX 655-1859J for a solid state drive. (a) Will this fit my iMac 2017 27-inch with the goofy tiny 28GB PCIe SSD and 1TB Fusion? (b) And, what might its performance be like in my iMac 2017? Yes, I know it’s quite a hassle getting to the 28GB PCIe SSD but I’m quite confident I can do it and do it well. Just figured since I want to increase the storage on my MacBook Air I might as well improve the lousy 28GB PCIeSSD.… Read more »

Guest
Carl Chen

I just read your Ultimate Guide. Excellent.. Superb contribution to the Mac community. Still puzzled though… My MacBook Air (2015) has a Model MZ-JPV512R/0A2 512GB SSUBX 655-1859J for a solid state drive. (a) Will this fit my iMac 2017 27-inch with the goofy tiny 28GB PCIe SSD and 1TB Fusion? (b) And, what might its performance be like in my iMac 2017? Yes, I know it’s quite a hassle getting to the 28GB PCIe SSD but I’m quite confident I can do it and do it well and my 1-year warranty is just about expired anyway and I learned too… Read more »

Guest
leo

I have MacBook Air 2017 model and I bought (Samsung 860 EVO 500GB M.2 SATA Internal SSD (MZ-N6E500BW) please tell me which connector will work to fix this SSD on macbook?

Guest
Kent Jenkins

Amazing article, Cody. I have this bookmarked where I work for ease of reference. Do you have plans to update this for the further changes? I know that Apple is getting further from updatability, but the insight speaks volumes to the capability and direction of these machines.

Thanks!

Guest
charles Brown

This is an OUTSTANDING article. Thank you so much for explaining all of this! I am sure it took a lot of time to gather all of that info. Do they make an adapter to retrieve data off of a Gen5A SSD yet?

Guest
David Loveridge

I don’t normally comment, but this article is so comprehensive I just had to say thanks!!!!!

Guest
Erika Howard

Does anyone know the newest SSD I could buy for my Mid 2014 128? I am confused on if there is backwards compatibility between generations.

Guest
Christian Majewski

Cody, thanks for your efforts in this interesting theme. I got two questions, and I am a perceived expert but no geek. 1) My late 2013 MB PRO shows A1398 on its label underneath and I see this model in your article in conjunction with the GEN 4, PCIe 3.0 NVMe. May I consider my model A1398 may have this abilities ( I can see “NVMExpress” in systems report though )? 2) Are there any compatible SSD available that I may consider to buy or do all have to be Apple certified or licensed by Apple ( I assume all… Read more »

Guest
Christian Majewski

.. my third question is, if I should buy a GEN5 SSD for about 500,- – 1.000,- USD as a Memory upgrade or rather a complete MB PRO that comes with this SSD?

Guest
Ralph

Cody, awesome work. Been searching the net for a couple of days trying to get a handle on upgrading my 13″ EARLY 2015 MBP (a1502) – Best option I can see for a 2TB card is an OWC Aura Pro X SSD but it’s pricey!!! $800.00 +/- 2TB Would you have or does anyone else know of other recommendations as to where/who might be making quality SSD(s) that I can look at? Needs to be a1502 compatible, I’ll be looking for a better price or waiting for a price drop from the current $800.00 +/- Thanks for your research and… Read more »

Guest
Luke Monahan

Thanks for the info.

Guest
Travis

A friend of mine gave me a couple of these apple ssd’s (one is a ssubx and the other ssuax) both in 512gb size. Is it possible to slap these puppies into an adapter and use them in an external or possible a PCI conversion for a PC use?

Guest
Peter

So if the SSUAX 1 TB is 2.0×4, there should not be any speed difference (or at least not a large one) compared to a SSUBX 1 TB drive when used in a MacBook Pro Retina 2014, correct? Any small improvements would be due to the newer controller and/or faster flash chips, because 2014 model would only use PCIe 2.0 even with the SSUBX drive?

Guest
Max

Hi,
Thanks for this unique article.
I have an imac 27″ late 2013 emc 2639. I’m trying to understand if i can purchase a third party PCI-e ssd or I have to go for an original Apple Spear.
Thanks for your HELP

Guest
Eric Jeoung

Very glad I found this guide. It is the most informative piece on the web. Thanks!
Still want to be definitely sure about one detail. Are all the Gen 4A drives interchangeable? Say Samsung ssd model MZ-JPV1280/0A3 for 2015 Macbook pro and model MZ-JPV128S/0A2 for 2015 Macbook air. If I switch them in places, can they work? Or should I be concerned about their different firmware?

Guest
Alican

Hi, thank you for the comprehensive information…I have 27 inch Late 2015 iMac, I intend to keep the 24GB fusion drive and swap 1TB Sata hard disk for a SSD. To what degree would this improve my hard-disk speed/performance ? Which brands/models are compatible to do this ?

Guest
waran

Hi,
I have a iMac 27” late 2012. EMC2546
Does this imac have a 7+17 Pin SSD connector?

Now I have got a SAMSUNG NVME SSD 960 EVO M.2 500GB SSD for upgrade.

1. Will this ssd blade support for my imac?
2. If works can i just replace the ssd or do i need an adapter (like Sintech ST-NGFF2013-C adapter for 2013 model) So can anyone help me to get the correct adapter model no for the late 2012 imac 27”??

Thanks in Advance!

Guest
George

Hello.
My Imac 21,5 Late 2012 / Core i5 , 2,7 / GeForce 640
Upgraid – SSD Samsung 850 EVO 1tb / 16 gb memory
On the motherboard there is a connector for flash drive SSD
Although stated that my model does not have this connector…
But it is..
Question:
Which flash SSD will fit ?
7-12 pin connector ?

Guest
Bern

Hello, I would like to upgrade the SSD on my Macbook Pro 15 Retina Mid 2012 A1398 from 512GB to 2 TB. I am considering Samsung SSD EVO 860 SATA III M.2 2TB using an adapter plate or OWC AURA PRO 6G 2TB. Do you have any concerns with compatibility or performance with these 2 scenarios? Are there better options? Thank you.

Guest
Alfredas

Wonderful article! The only bit missing – you haven’t specified Gen. 5 – which models use A and which B. It would be great, since standard 2019 iMacs have built-in problematic Fusion Drive (and 1TB version is a joke nowadays) and Apple charges a great deal with built-to-order SSD-only upgrades, it would be nice to know, what SSD are suitable for each 2019 iMac model. Thank you!

Guest
Manveer Dhillon

When will you guys stock up on the sspolaris 2TB SSD?

Guest
Cédric

Hello,
I have a iMac i5 5K 2017 originally configured with a 512GB SSD. But 512GB quickly became insufficient. Plus I’m working with Final Cut Pro X, which will point me to a new NVMe hard drive.
However, I read here and there that sometimes it could cause some dysfunction. But I also read that it could be a fast and reliable one.
Who is right ?
And if the NVMe option becomes positive, what hardware would you suggest to buy? Disc, temperature sensor, adapter …
Thank you for sharing your knowledge.

Guest
Robert

So as I understand it, the 2015 MBA 13” SSUBX drive is the same as a 2015 MBP 15” SSUBX (both PCIe 3.0 x 4 NVMe) and work at the same speed? Have a higher capacity SSD from a MBA that I want to replace my MBP drive with, and what to make sure it will work at the same speed as an original MBP drive.

Guest
Mahdi Hedhli

I’ve got a challenge for ya. The OWC Accelsior E2 uses 2x 18 pin mSATA SSDs. It’s the same form factor and voltage (3.3vdc) as the 2012 and earlier Macbook Air SSDs but the amperage is much lower (0.8a vs 1.2-1.55a). Looking for a compatible drive or adapter. Whatcha got for me?

Guest
Fabio M

I just went to the beetstech looking for a ssd for my 27” iMac late 2013, and the compatibility check said ’not compatible’…

Member
jim

Very good and informative article. Does anyone know if the 16+12 blade is able to work in an external case, SATA to be exact? I have seen USB carriers but SSD has eluded me. Trying to do recovery on a fusion array. USB is too slow.

Guest
Ken

Great article Cody…but unless I missed it, there’s no info about the Mac Mini Late 2012 or Mac mini Server of the same vintage. Can you possibly speak about the types of connectors for these? Thank you.

Guest
Florian

Thanks a lot for this great resource!

Just one thing: The PCIe Speed Comparison Chart lists double the Effective Data Rate than other sources (e.g. Wikipedia), and also the math suggests that your numbers are too high.

Guest
Frank

Fantastic information gathering here, Cody! But I think there is an error in your PCIe Speed Comparison Chart. In the last column (the second one labeled “Effective Data Rate”), it looks like all the values are overstated by a factor of 2X. For example, 2-channels of PCie 2.0 should support a maximum effective data rate of 1GB/s, NOT 2GB/s. (4Gbits/s for each channel)*(2 channels) = 8Gbits/s ,or 1GBytes/s effective rate.

Guest
John Greene

What a great article. Helped me realise that the MBAir early 2015 SSD is different from the other sized MBAirs of early 2015 … possible incompatibility to external enclosures tat state compatibility to early 2015 MBAir original SSDs.. Thank you

Guest
Kate Gehle

Cody,
Thank you so much for the thorough and superbly written details!!! I like to upgrade my iMac myself and it’s been challenging finding out exactly what type of SSD could be used in the 2017. I assumed Nvme (there’s also an adapter available to go standard pins for an M.2 Nvme) and your article confirmed that.
Great job!
Kate

Guest
Luis

Hi. Besides , will the A1708 with 8GB perform well with an SSD upgrade (from 128 GB) to 250GB? Thanks

Guest
Michael

Hi, I have a mid 2014 MacBook Pro and would like to upgrade the SSD in it. Would a Gen 4A work for this model? Also, would it benefit from the x4 in this case or no?

Guest
James

is there a diff. between model num. 656-0020a and model 656-0021a For macbook air 2015, 11 inch, ssd?

Guest
Emilio

Hi! I discovered that my iMac (Retina 5K, 27 inch, 2019) 1TB HDD shares space with a small 28 GB SSD (Fusion Drive). What could be the best choice to have better performance with a new SSD (even if a little bit tricky to upgrade)? Is it worth it? Or is it better to ignore that SSD and change the main HDD with an SSD? So, the first solution is to have the fusion drive working, upgrading only the SSD (SSD blade 28gb), or second solution lose the fusion drive and upgrade the main HDD with a more efficient SSD?

Guest
Felix

I use a MacBook Pro 13″ mid-2014 and I want to upgrade from 128 GB to 256 GB but I do not want to lose battery time. Do SSDs of the 4. generation use more energy than the 3. generation SSDs? Thank you for this article and it would be nice if you could answer my question.

Guest
Tango Cash

Just wondering if I can use 2TB NVMe SSD for Late 2013 Macbook Pro? 1TB is surely cheaper but I’d like to buy 2TB if it can be used.

Guest
Dik Hedlund

I need to replace my 2017 Macbook Pro(A1708) as it sustained water damage. Do the new 2019 MacBook Pros use the same 5A Gen drives w/22+34 connectors? I need to be able to transfer data from my older SS HD.

Guest
James

Purchased a Gen4 Apple SSD (NVMe capable) of 512Gb to upgrade my Mac Mini 2014. Recognised by MacOS as PCIe drive but using SATA communications protocol. Does not see new drive as NVMe device.

How do I get the SSD to be recognised as an NVMe device ??

Guest
Bob Culbertson

I’m curious to know who makes the optional SSD in the mid-2017 iMac 21.5″. Is it proprietary or made by Samsung? Thanks.

Guest
Pico

I’ve learned and confirmed from experience that if you put an NVMe Blade SSD into a Mac that shipped with a SATA Blade SSD (such as putting an NVMe Blade SSD into a 2015 MacBook Pro or into a 2013 Mac Pro, etc), that the Macs EFI Firmware will never get updated during system updates. If you put back in the original drive and re-run the system update, then the EFI Firmware will get updated properly. If this extremely useful blog post is still getting updated, I think it would be very important to add this note for anyone who… Read more »

Guest
Igor

Guys, I have MacBook Pro 15 Retina mid-2014 with original 1 Tb SSD installed. Is it possible to put this 1 Tb SSD in a new iMac 27 5k 2019 instead of native 32 Gb SSD (as a part of 1 TBFusion Drive)?

Guest
Nacho

Hi, excellent article!!
I’m thinking of upgrading the 256GB on my early 2014 13′ MacBook Air.
On “System Report” I read PCI 5GT/s x2 but your article says the logic board has x4 channels.
Can you confirm what is the max speed I can get? I was thinking on a Samsung 970 EVO SSD+adapter, but I want to make sure I’ll get what I’m paying for…
Thanks again!

Guest
VicMarsh

I’m looking to increase the SSD in my MacBook Pro mid 2019 (MV902LL/A) from 256 to 1TB. Is there a compatible SSD I can install on my own, or does it need to go to Apple?

Guest
James

Great article Cody.

Any chance you could update it with the 2017 iMac 5k SSDs please?

Guest
Michael Caffin

Hi,

I have a mid-2012, Airbook, A1466 Model, and purchased the Samsung 970 EVO. I had no foreknowledge in regards to technology. Subsequently, I realized that it did not fit, and also could not find an adapter.

Do you recommend using the Samsung 970 EVO, understanding it is a different technology, or look for a SATA third party – I need to better understand if I’d purchase a third party SATA if it will help to run my computer a little better to deal with Catalina. Thanks!

Please, advise

Member
Michael McGowen

Great article, Cody! Thank you for posting this.