Why Disk Utility lists a new Mac SSD as a 1 GB disk
After an Apple SSD is installed in an older Mac, Disk Utility sometimes lists a disk of only about 1 GB. Erase is greyed out, and the macOS installer offers no disk to install on.
That small disk is almost never the SSD’s capacity. Two different causes produce the small disk, and the name beside the size tells them apart. Each cause has its own fix.
Table of contents
Which small disk is it?
The name of the small disk in Disk Utility points to one of two cases:
- “OS X Base System” or “macOS Base System”, 1.2 to 2.2 GB, described as an Apple disk image. This is the Recovery image the Mac started from, and the SSD is missing from the list. See case 1.
- “SM_NVMeROM Media”, exactly 1.07 GB, under Internal with a PCI-Express connection. This is the SSD itself, in a fallback state. See case 2.
Case 1: the Recovery image
macOS Recovery and the macOS installers run from a small, read-only disk image. Disk Utility lists that image as “OS X Base System” in older versions and as “macOS Base System” in newer ones. The image holds Disk Utility and the installer, not a full copy of macOS, so the image is only 1.2 to 2.2 GB.
Older versions of Disk Utility even name the image disk0, the name that a Mac’s internal drive usually gets. So the image is easy to mistake for the new SSD. Erase and Partition are greyed out because the Mac is running from the image.
OS X Recovery on a Late 2013 MacBook Pro with a new SSD installed. The only disk listed is the 1.28 GB Recovery image, described as an Apple disk image.
Why the SSD is missing
The blade SSDs from the 2017 and 2019 iMacs (Gen 5B in our guide to Apple’s SSDs) use the NVMe protocol, with a Samsung controller that Apple names SSPOLARIS. Macs from 2013 to 2015 shipped with older AHCI drives. They also shipped with versions of OS X released before these drives existed. Recovery or an installer for one of those OS X versions cannot detect a Gen 5B drive, so Disk Utility lists only the Recovery image.
We tested one 128GB Gen 5B drive in a Late 2013 15-inch MacBook Pro. The OS X 10.10 installer listed no internal drive. The macOS 11 installer listed the same drive under Internal, at its full size.
The OS X 10.10 installer on that MacBook Pro. Disk Utility lists the USB installer and the 1.33 GB Recovery image, and no internal drive.
The macOS 11 installer on the same Mac, with the same SSD. The SSD is listed under Internal at 120.88 GB.
Why Command-R starts the old Recovery
An Intel Mac has three key combinations for Recovery, and each combination loads a different version of macOS (Apple’s instructions):
- Command-R starts the Recovery on the startup disk, for the macOS installed most recently.
- Option-Command-R starts Internet Recovery for the latest macOS compatible with the Mac.
- Shift-Option-Command-R starts Internet Recovery for the macOS that came with the Mac, or the closest version still available.
A new, blank SSD holds no Recovery of its own. In every case we have seen, Command-R then started Internet Recovery for the version of OS X that the Mac shipped with, such as OS X 10.9 Mavericks on a Late 2013 MacBook Pro. That version is too old to detect the SSD.
The fix
- Shut down the Mac.
- Press the power button, then hold Option-Command-R until a spinning globe appears.
- Check the Recovery window: the window should offer to reinstall macOS 10.13 High Sierra or a later version.
- Open Disk Utility, then choose View > Show All Devices.
- Select the SSD under Internal. The SSD’s name starts with “APPLE SSD”, and the SSD’s size matches the drive’s capacity.
- Click Erase, choose APFS and GUID Partition Map, and click Erase again.
- Quit Disk Utility, then choose Reinstall macOS.
macOS 11 Recovery on the same MacBook Pro. The SSD is listed under Internal as APPLE SSD SM0128L Media, and the Recovery image is listed apart, under Disk Images.
The Internet Recovery error screen. The second try started normally.
A USB installer for macOS 10.13 or later avoids Internet Recovery altogether. How to create a bootable macOS install USB drive shows how to make one. The free app Mist downloads the installer and makes the USB drive in one step.
Firmware for starting up from the SSD
A Mac from 2013 to 2015 starts up from an NVMe drive only with an updated Boot ROM, the Mac’s firmware. That update first came with macOS 10.13 High Sierra. Apple ships firmware only inside macOS installs and updates, so a Mac that has had High Sierra or later installed normally has the update already.
The free app SilentKnight shows the firmware version and whether that version is current. If the firmware is old, install a current macOS on the original drive first, then install the new SSD.
SilentKnight on a Late 2013 MacBook Pro (MacBookPro11,3). The firmware version found matches the version expected.
Case 2: SM_NVMeROM Media, 1.07 GB
In this case Disk Utility does list the SSD under Internal, with a PCI-Express connection. But the name is “SM_NVMeROM Media”, and the size is 1.07 GB whatever the drive’s real capacity. The drive is “Uninitialized”, and the partition map is “Not Supported”. System Information lists the model as SM_NVMeROM, the revision as SMROM001 and the serial number as SM_ROM_DEFAULT_SN.
The drive cannot be erased. A newer macOS does not help either: the screen below is from the Recovery for macOS 12 Monterey.
A 512GB Gen 5B SSD in a Late 2015 21.5-inch iMac, in macOS 12 Recovery. Disk Utility lists the drive as SM_NVMeROM Media, 1.07 GB.
What the state is
Samsung makes the controller in these drives. At power-on, the controller loads its firmware from the drive’s flash memory and checks the firmware. When that check fails, the controller runs from a small program built into the chip (its ROM) instead. The controller then reports a placeholder identity. Samsung’s documentation for its NVMe drives lists that identity: the model SM_NVMeROM and the serial number SM_ROM_DEFAULT_SN.
The flash memory cannot be reached in this state, so the drive cannot be erased, partitioned or used.
Where the state appears
Every report of this state that we have, where the Mac is known, came from a Late 2015 21.5-inch iMac (iMac16,1 or iMac16,2) with a Gen 5B drive. One of those iMacs also had kernel panics that named the NVMe controller and “PCI link down”.
The state does not appear every time. One drive that showed the state passed every test afterwards in our own Late 2015 21.5-inch iMac. The Late 2015 27-inch iMac (iMac17,1) has a related fault with these drives: kernel panics on wake from sleep.
Which SSD a Late 2015 iMac should use
The state can be neither predicted nor cleared, so Gen 5B drives are not compatible with Late 2015 iMacs of either size. These iMacs should use Gen 4 SSDs, the generation that the iMacs shipped with. Gen 4 drives use the AHCI protocol and work with every macOS version these iMacs can run, with no firmware update.
USB adapters cannot read these drives
USB adapters and enclosures for Apple’s 12+16-pin SSDs are built for the AHCI drives of 2013 to 2015 Macs. The adapters we know of state that NVMe drives are not supported. A Gen 5B drive in one of these adapters is not detected at all, so an adapter cannot be used to test a Gen 5B drive.
Our guide to Apple’s proprietary SSDs lists every generation and the Macs that each generation fits. How to use the built-in Recovery Mode for macOS walks through Recovery step by step.
Like this post
Recommended posts
High Sierra and Testing RAM
With macOS 10.13, otherwise known as High Sierra, Apple introduced an ambitious EFI update. Several of the changes include: the introduction of the Apple File System, support for NVMe drives, and the usual batch of security updates. However, these EFI updates can cause some unwanted behavior when you test your Apple computer’s memory. At Beetstech, we use a long-time industry standard, MemTest86 to perform a comprehensive test of each computer’s RAM.
But never the type to blindly accept test results, strange testing outcomes led us to discover a bug in MemTest86 affecting computers running the new EFI firmware. In short, the newly updated EFI causes MemTest86 to incorrectly fail certain tests. But there is good news: while normal operation of MemTest86 is limited under these new EFI updates, we also discovered some simple workarounds for testing your Apple’s memory in MemTest86.
So let’s dive into how we discovered the MemTest bug, devised a reliable work-around, and get into some nitty gritty details of MemTest86 operation.
MacBook Air Power-On Pads – Location & Use
They go by “jumper pads”, “short-circuit pads”, “power pads”, and “power-on pads”. Whatever you call them, there are two bits of metal on your MacBook logic board that can force your laptop to boot up, even if the power button won’t do the trick.
OEM MagSafe Chargers vs Cheap Imposters: Teardown for Truth
Anywhere premium products are produced, there are unsavory folks trying to make a quick buck selling cheap knockoffs. It happens in every industry, from clothes to food to tech. But in recent years, counterfeit electronics have surpassed nearly all other categories of counterfeit goods by dollar value, and Apple, being the de facto high-end electronics manufacturer, makes for a prime target.
But you’d never be caught buying counterfeit electronics, because you can tell the difference, can’t you?
The Ultimate Guide to Apple’s Proprietary SSDs
Remember the good ol’ days of carrying a spare battery, upgrading your own RAM, maybe even adding a second hard drive? If you’re an Apple user, those luxuries may be behind us, but upgrading your own solid state drive is still a privilege the Apple overlords allow us to have, for now that is.
Despite retaining the ability to upgrade your own SSD, ever since Apple introduced their proprietary “blade” SSDs in 2010, the task hasn’t been as simple as it once was. Apple talks up read and write speeds, but they rarely dive into the nitty gritty details of the technology behind the SSDs they use — drives specially designed only for Apple computers.
After countless questions, both from customers and our own staff, we decided to start our own investigation into the hardware involved. You have to be a bit of a private eye to uncover the secrets behind these drives, and the deeper we looked, the more surprises we found.
Your Hard Drive Cable Is A Ticking Time Bomb
Owners of a Unibody MacBook Pro laptop are probably already aware that failure of the hard drive flex cable is a common issue. While it affects just about the entire Unibody lineup, the Mid 2012 MacBook Pro 13″ (Model A1278) is especially prone to this type of failure.
What is it that makes the Mid 2012 release special in this regard? A design flaw in the flex cable that seems to be compounded by the properties of the aluminum housing.
Our repair services department noticed this issue when they’d replace a bad cable, only to have the customer return a few months later with another bad cable. And possibly again with yet another bad cable. It didn’t matter if we used a used cable or a new cable in the replacement. Customers kept returning with the same persistent issue. We had to figure out what was causing the issue and find a solution.
Comments